---
title: "Does an air-to-water heat pump still work in snow and frost?"
date: 2026-11-16
author: "Rachel Nijsen"
featured_image: "https://aosmithinternational.com/wp-content/uploads/2025/09/Copy-of-Copy-of-Untitled-Design.png"
categories:
  - name: "News"
    url: "/category/news.md"
---

# Does an air-to-water heat pump still work in snow and frost?

## Does an air-to-water heat pump still work when it freezes or snows?

Yes, a well-designed heat pump installation can still provide heat for domestic hot water and space heating when it snows or freezes. However, efficiency and available capacity change as outdoor temperatures drop.

For buildings with a high or continuous hot water demand, it is important to select the right capacity, provide sufficient heat storage and, where needed, include an additional heat source. In this article, you will learn what winter weather conditions mean for heat pump performance, water temperature and the availability of domestic hot water.

![Air-to-water heat pump in snow and frost](https://aosmithinternational.com/wp-content/uploads/2025/06/image-1024x577.png "1")## Does a heat pump work in winter?

An air-to-water heat pump extracts energy from outdoor air. Even when temperatures are below zero, there is still heat available in the air that a heat pump can use. The heat pump uses electricity to raise this heat to a usable temperature for domestic hot water, heating or cooling.

When outdoor temperatures fall, a heat pump has to work harder. As a result, efficiency decreases and the available capacity may drop. This does not mean that a heat pump stops working in freezing conditions, but it does mean that the system needs to match the hot water demand, required temperature and local design conditions of the building.

## What do COP and SCOP mean for a heat pump?

COP stands for *Coefficient of Performance*. It is the ratio between the thermal energy produced by the heat pump and the electrical energy it consumes at one specific test condition.

SCOP stands for *Seasonal Coefficient of Performance*. SCOP takes account of seasonal changes, varying outdoor temperatures, part-load operation and the capacity needed for heating. To determine SCOP, heat pumps are tested at different outdoor temperatures, loads and flow temperatures:

- 30/35°C for low-temperature heating;
- 47/55°C for medium-temperature applications;
- 55/65°C for high-temperature applications.

For each of these flow temperatures, the measurements provide an average efficiency over the full heating season. For example, the Enevator Air Altus has a SCOP of 3.95 at low temperature according to the product data used. This means that the unit produces an average of 3.95 kW of heat over the season while consuming 1 kW of electricity.

A high COP or SCOP is valuable, but it is never the only selection criterion. Actual performance depends on outdoor temperature, required water temperature, hot water demand, peak loads and the design of the complete installation.

## Climate zones in Europe and energy labels

For SCOP calculations and energy labels, Europe is divided into three climate zones: warm, average and cold. These zones are based on the reference cities Athens, Strasbourg and Helsinki.

Climate conditions can vary significantly between countries, regions and altitudes. For this reason, the local design outdoor temperature should always be taken into account when selecting an air-to-water heat pump.

Energy labels make it easier to compare product performance. However, a project-specific calculation remains essential for a reliable heat pump installation. Read more about [energy labels](https://aosmithinternational.com/le-label-energetique/).

![Energy label for an air-to-water heat pump](https://aosmithinternational.com/wp-content/uploads/2025/06/Picture4.png "2")## Does snow affect an air-to-water heat pump?

Snow itself is not a reason why an air-to-water heat pump would stop working. However, the outdoor unit and airflow must remain clear. When designing and maintaining the installation, it is important to consider snow, frost and defrost water.

- Provide sufficient free space for air intake and discharge.
- Prevent snow, leaves or dirt from blocking the grilles.
- Make sure defrost water can drain away properly.
- Consider snow that could fall onto the unit from a roof or structure.
- Keep the unit accessible for inspection and maintenance.

For commercial and industrial hot water installations, weather conditions are only one part of the equation. Hot water peaks, continuity of supply, storage capacity and controls are also important.

## Is a gas-fired or electric back-up water heater needed in winter?

Do you still have a well-functioning boiler or gas-fired water heater? It does not always need to be removed straight away. It can continue to work alongside the heat pump. If outdoor temperatures become so low that the heat pump cannot provide enough capacity, the boiler can support space heating, while a [high-efficiency water heater](https://aosmithinternational.com/product-ranges/condensing-water-heaters/) or an [electric water heater](https://aosmithinternational.com/product-ranges/electric-water-heaters/) can provide additional domestic hot water capacity.

There is another good reason to consider a back-up. As outdoor temperatures decrease, heat pump efficiency decreases too: the COP drops. Depending on gas and electricity prices, there can be a point at which it is financially attractive to use a gas-fired or electric water heater alongside the heat pump. This can, for example, be the case at outdoor temperatures below 0°C, but it differs per installation and energy price.

At extremely low temperatures, outside the operating range of the selected heat pump, additional heating may be required. If you choose an electric water heater, you have both a back-up and a fully electric solution in one. A hybrid system combines heat pump technology with additional capacity, helping to ensure sufficient hot water during cold periods and peak demand.

Winter conditions vary considerably by location and altitude. In colder regions, the design outdoor temperature can be much lower than in milder areas. It is therefore important to select both the heat pump and any back-up solution according to the local climate, hot water demand and required water temperature.

## Example: Enevator Air Altus at low outdoor temperatures

The Enevator Air Altus is a modular air-to-water heat pump for larger applications. This heat pump has a COP of up to 5.5. This means that, under the relevant test condition, the unit can produce up to 5.5 kW of thermal energy using 1 kW of electricity.

The actual COP depends on factors such as outdoor temperature, required flow temperature and system load. As outdoor temperatures fall, efficiency decreases and available capacity may drop. A heat pump should therefore not only be assessed on its maximum COP, but also on its performance at the building’s design conditions.

![Heat pump system diagram](https://aosmithinternational.com/wp-content/uploads/2025/06/Picture2.png "3")Enevator Air Altus AWHA 88

![Enevator Air Altus performance at low outdoor temperatures](https://aosmithinternational.com/wp-content/uploads/2025/06/Picture3.png "4")The product curve shown illustrates that the achievable hot water temperature may decrease as outdoor temperatures fall. In this example, the Enevator Air Altus can deliver water temperatures of up to 70°C at an outdoor temperature of 0°C or higher, 65°C at -10°C and 55°C at -20°C. Always check the latest technical documentation and performance data for the selected configuration.

## Why are hot water temperature and capacity important?

For domestic hot water, sufficient capacity alone is not enough. You also need the required temperature and sufficient capacity during peak demand. A water temperature of 55°C is not sufficient for every domestic hot water application. This depends on hygiene requirements, the required end temperature and legionella risk management.

An additional heat source can support the heat pump during a cold period and raise the water temperature further. For low- or medium-temperature space heating and cooling, additional heating is not always needed to reach the required flow temperature. However, keep in mind that the capacity of an air-to-water heat pump decreases as the outdoor temperature falls.

For a reliable hot water installation, the heat pump, storage tank, buffer tank, controls and any additional heating should be properly matched.

## When is a booster heat pump a solution?

When an air-to-water heat pump preheats water efficiently but a higher final temperature is needed, a booster heat pump can be an interesting solution. The Enevator Aqua Booster is a water-to-water heat pump. It does not extract heat from outdoor air, but uses heat from water that has already been preheated by another heat source.

An air-to-water heat pump can efficiently preheat the water. The Aqua Booster can then raise the temperature further, up to 78°C. This combines the high efficiency of an air-to-water heat pump with the higher temperature that may be required for domestic hot water.

This combination can be particularly suitable for buildings with a high hot water demand and a need for a reliable, high domestic hot water temperature. Examples include hotels, sports facilities, care homes and other commercial or industrial buildings.

This combination can also be valuable in winter. At lower outdoor temperatures, an air-to-water heat pump may work less efficiently or deliver a lower water temperature. A booster can then help reach the required final temperature without the air-to-water heat pump having to deliver the entire temperature rise on its own.

## Frequently asked questions about heat pumps in freezing conditions

### Does an air-to-water heat pump work when it snows?

Yes. An air-to-water heat pump also works when it snows, as long as the air intake and discharge of the outdoor unit are not blocked. A suitable installation position, proper defrost water drainage and regular maintenance are important.

### Does a heat pump still work in freezing temperatures?

Yes, a heat pump can still produce heat below 0°C. However, efficiency decreases as outdoor temperatures fall and available capacity may also decrease. Correct sizing is therefore essential.

### Is a back-up required with a heat pump?

That depends on hot water demand, the required temperature, the selected heat pump and the required level of continuity. In case of high peak demand or a high final temperature requirement, additional heating can be an appropriate solution.

### How can you ensure enough domestic hot water in winter?

By matching the heat pump installation to the actual hot water demand. The correct capacity, heat storage, controls and any additional heating are all important.

## Conclusion

To return to the main question: does an air-to-water heat pump still work in snow? Yes, a heat pump also works below freezing point and in snowy conditions. It works most efficiently at milder outdoor temperatures, but can still provide heat for domestic hot water and space heating in cold weather.

With the right sizing, sufficient heat storage, effective controls and, where needed, an additional heat source, you can create a reliable heat pump installation. Do you need support with your installation? [Contact A.O. Smith for advice.](https://aosmithinternational.com/customer-area/)